 |
|
Factory Installed Valves,
Slide Bars and Hardware |
|
|
|
|
|
|
All catalog items range
from a bare shell, to factory drilled valve holes, to a
completely turn key unit that includes a factory installed
valve, slide bar, and shower head. At this level you just
plumb in water, attach the drain, screw the unit to the
stud pocket and your done!
We can even add additional grab bars or install customer
supplied valves or other hardware. |
|
|
|
|
▲
Top of page |
|
|
|
Barrier-Free Splash Guard |
|
|
|
Glued down with silicone caulking in the
entry way of our barrier free models to help retain water in
the shower fixture and off of the floor in front of the
shower.
Designate: ESPLASHGUARD T, ESPLASHGUARD D and ESPLASHGUARD-PC
when ordering. |
|
|
|
SPLASHGUARD T All Rubber |
|
 |
|
|
SPLASHGUARD D All Rubber |
|
 |
|
|
SPLASHGUARD PC Aluminum barrier-free water dam |
|
 |
|
|
|
▲
Top of page |
|
|
|
H4PH ## Four-Legged,
Wheelchair Transfer Seat |
|
|
|
This seat complies with ADA requirements. Use
this seat for retrofitting an existing
barrier-free shower or in commercial applications where weights
greater than 350
pounds may be encountered. Seat and legs fold up against the
wall when the seat is not
needed. Fits Fiber-Fab Models # 38H1, 40H1KD, 48H1, 60H1,
60H1KD and 63H1. |
 |
products only |
|
|
|
|
|
 |
|
|
|
▲
Top of page |
|
|
|
|
|
Temptrol 2000 pressure-balancing mixing valve
with built-in choke and adjustable stop
screw to limit handle turn and integral service stops. |
|
|
|
 |
Tub/Shower VS252X |
|
|
|
 |
Shower VS251X |
|
|
|
▲
Top of page |
|
|
|
|
|
Standard Lengths: |
|
|
12” (305mm) |
|
36” (914mm) |
16” (406mm) |
40” (1016mm) |
18” (457mm) |
42” (1067mm) |
24” (610mm) |
48” (1219mm) |
30” (762mm) |
52” (1321mm) |
32” (813mm) |
54” (1372mm) |
|
|
|
 |
|
|
|
Straight Bars
This bar can be mounted horizontally, vertically or
diagonally for use individually or in combination with
other grab bars. All bars are 11/4“ in diameter with
concealed screw flanges and are 18 gauge. Additional bar
configurations, finishes and coatings are available by
special order.
Field Installation of Grab Bars
Installing grab bars in existing Fiber-Fab bathtubs and
showers does not require additional backing. Because
Fiber-Fab’s units have an extremely high content of resin
and fiberglass and low filler content, the strength and
rigidity needed to support the mounting of grab bars are
inherent to the product (Fiber-Fab is the only
manufacturer that can make this claim).
In mounting the grab bar(s), we recommend using a
stainless steel, #10 wood screw, 2” long with threads all
the way to the head of screw. |
|
| |
|
▲
Top of page |
|
|
|
|
|
|
|
|
|
|
This solid brass grab bar
is beautifully sculpted, combining strength and design for
a safe entry and exit from the bathing fixture.
Once installed, it can be easily removed from inside the
tub or shower to accommodate last minute changes.
Available in a variety of finishes including polished
chrome, polished brass, white and brushed chrome. |
|
|
GB7-PC |
|
Polished Chrome |
GB7-C1 |
|
Brushed Chrome |
GB7-N1 |
|
Brushed Nickel |
GB7-P1 |
|
Brushed Pewter |
GB7-BC |
|
Biscuit (Powder Coated) |
GB7-WH |
|
White (Powder Coated) |
GB7-PB |
|
Polished Brass (PVD finish) |
GB7-OB |
|
Oiled Bronze |
|
|
|
|
|
|
|
Shower Curtain, Rods and
Hooks |
|
|
|
Are available in two styles.
VINYL (ECSVC ##WH) Vinyl film .008 mil. FLAME-RESISTANT (ECSCFR ##WH) Vinyl-Laminated
fiberglass with flame, static, bacteria and mildew resistance.
Curtain Rods
Are available in two styles.
|
|
 |
|
|
|
H733PH Folding Shower Seat |
|
|
|
This “L”-shaped seat is designed to comply
with ADA requirements. The seat is constructed of white
phenolic and is supported by a stainless steel frame. When not
in use, the seat folds up against the wall. Available in three
different sizes. Weight rated for 250 pounds. |
|
|
|
|
products only |
|
|
|
|
|
|
|
|
|
H703PH Folding Shower Seat |
|
|
|
Frame is stainless steel Type 304, 1"x18
gauge satin finish. Legs angle into base of wall
for rigid support. When not in use, seat folds up against wall
to conserve space and
thumb screw holds it in place. Seat measures 18" long and
projects 15½" from wall. |
|
|
|
|
|
|
|
Removable Threshold Model
ERT ## |
|
|
|
This threshold can be field installed in
our Assisted Living Models #38, 60 and 63 to help
retain water. When shower needs to be converted to an ADA
compliant shower, the
threshold can be easily removed. Available in Satin Stainless
Steel, Polished Stainless
Steel or White Powder Coat. Splashguard not included. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
